Step by Step Guide to Updating VMware ESXi 5.0 to 5.5 on SYS-E32 (Soyoustart / OVH)

Discussion in 'Networking Guides' started by Nimrod, Feb 8, 2014.

  1. Nimrod

    Nimrod Exotic Vendor

    Joined:
    Jun 1, 2007
    Messages:
    1,991
    Likes Received:
    533
    Location:
    London, United Kingdom
    On the SoYouStart control panel you can fresh install Esxi 5.0, however this is quite an old version with 5.1 and 5.5 being released. However, you can upgrade it within just a few minutes without waiting for OVH to release a pre-made installer for them. All that’s required is an SSH client (like Putty on Windows, or Terminal on Mac) and a few commands.


    Let's get started:


    First of all, SSH into your Esxi installation using Putty (or Terminal).


    Copy and paste the below command and press enter:


    Code:
    esxcli software profile install -d http://hostupdate.vmware.com/software/VUM/PRODUCTION/main/vmw-depot-index.xml -p ESXi-5.5.0-1331820-standard --ok-to-remove
    
    You will then get a result like below:


    putty1.PNG


    Your notice the first attempt I did, I got a broken pipe (Errno 32) on VMware_locker_tools_light


    This was due to the fact the server was running VM’s (or the vSphere connection) at the time. To get past this, I put the server into Maintenance Mode using the vSphere client as below:


    Maintance Mode.PNG


    Then give it another go, you should then get a successful response like on my second attempt on the first screenshot.

    Update: If you don't have vSphere you can use SSH to put your box into Maintenace Mode with the below command:

    Code:
    vim-cmd /hostsvc/maintenance_mode_enter
    Now stop just a moment before you reboot the box and enjoy your new 5.5 installation. Sadly 5.5 out of the box doesn’t have the network card (NIC) drivers needed for your SYS-E32 server. If you rebooted now it would be a disaster and you wouldn’t be able to get it back online without reinstallation.


    However an awesome community member called Chilly has compiled the latest Intel drivers for ESXi 5.5 which can be installed, just do the below:


    First of all, enable CommunitySupported VIB’s to be installed by running the below command:


    Code:
    esxcli software acceptance set --level=CommunitySupported
    
    Then run this command to install them:


    Code:
    esxcli software vib install -v http://files.v-front.de/net-e1001e-1.0.0.x86_64.vib
    
    All going well you should get the below:


    putty2.PNG


    At this stage, you can successfully type ‘reboot’ and let your box reboot itself onto 5.5. All going well, in a couple of minutes you can connect your vSphere client to your box and get the nice error messaging saying you need to update your client to 5.5. Update and you are good to go!


    Hope this helps.
     

    Attached Files:

  2. fredB

    fredB New Member

    Joined:
    Sep 24, 2014
    Messages:
    2
    Likes Received:
    0
    Thanks a lot Nimrod. you saved a lot of my time with your preocedure!
    It worked exactly as you wrote!
     
  3. TomF

    TomF New Member

    Joined:
    Nov 15, 2014
    Messages:
    1
    Likes Received:
    0
    That was a great post Nimrod. You explained it well and my results were verbatim to what you described. More OVH/VMware tips and tricks please :-)
     

Share This Page