Xbox 360 Jtag or RGH Hack Easy Update to Dashboard 17502 with XeBuild GUI

Discussion in 'Xbox 360 Guides' started by InsaneNutter, Aug 19, 2013.

  1. gdavies

    gdavies Elite Member

    Joined:
    Nov 25, 2013
    Messages:
    63
    Likes Received:
    14
    Location:
    Staffordshire
    I had that problem I connected my xbox to my router via ethernet did the same with my laptop and then ran XEBuild v 1.08 I had put the system update for 2.0.16537 into the folder called 16537, Powered up my xbox and went to dash launch then to configure and put updserv set to enabled, then on my laptop ran the file called updatemyconsole.bat

    It did the update for me and rebooted my xbox and now it doesn't ask for the kinect update either and the JTag is still there too
     
    ritorubi likes this.
  2. hyra

    hyra New Member

    Joined:
    Dec 22, 2013
    Messages:
    4
    Likes Received:
    3
    I tried it but it kept saying that "Fatal error occurred. Cannot find console" even though I already connect them through the router.
     
    ritorubi likes this.
  3. gdavies

    gdavies Elite Member

    Joined:
    Nov 25, 2013
    Messages:
    63
    Likes Received:
    14
    Location:
    Staffordshire
    you have to enable updserv via dashlaunch and keep dash launch open
     
    ritorubi likes this.
  4. hyra

    hyra New Member

    Joined:
    Dec 22, 2013
    Messages:
    4
    Likes Received:
    3
    ok that method worked finally, but after that the kinect still did not work.
     
    ritorubi likes this.
  5. gdavies

    gdavies Elite Member

    Joined:
    Nov 25, 2013
    Messages:
    63
    Likes Received:
    14
    Location:
    Staffordshire
    may need to redo it as it would seem something clearly has not gone over
     
    ritorubi likes this.
  6. InsaneNutter

    InsaneNutter Resident Nutter Staff Member

    Joined:
    Jun 1, 2007
    Messages:
    12,254
    Likes Received:
    3,724
    Location:
    Yorkshire, England
    All you need to do is run the 16537 update and this will restore the avatar / kinect data.
     
    ritorubi likes this.
  7. hyra

    hyra New Member

    Joined:
    Dec 22, 2013
    Messages:
    4
    Likes Received:
    3
    what do you mean by "run the 16537 update"?
     
    ritorubi likes this.
  8. gdavies

    gdavies Elite Member

    Joined:
    Nov 25, 2013
    Messages:
    63
    Likes Received:
    14
    Location:
    Staffordshire
    mens just run the update itself, I suggested what I did due to my console not seeing updates, did a bit of research and found other means, but you could download the system update put it on a disc and away you go
     
    ritorubi likes this.
  9. InsaneNutter

    InsaneNutter Resident Nutter Staff Member

    Joined:
    Jun 1, 2007
    Messages:
    12,254
    Likes Received:
    3,724
    Location:
    Yorkshire, England
    You have to get the kinect / avatar data from the official microsoft update.

    It is all explained in the first post under: 5. FAQ: How do I restore the avatar and kinetic data so i can use my kinect?
     
  10. azboy50

    azboy50 New Member

    Joined:
    Dec 30, 2013
    Messages:
    2
    Likes Received:
    0
    Is there a quick guide to doing this or just follow the instructions you put at the top of the forum. Can you email it to me azboy041666@gmail.com? I tried using xexmenu 1.2 but that didn't work. So any advise you can give me will help. Can you get this to me asap? Thank you so much sir. And happy New Year.
     
  11. MasterChief

    MasterChief Addict

    Joined:
    Sep 17, 2009
    Messages:
    743
    Likes Received:
    89
    Location:
    The Internet
    What's not quick about the above? if you read it you will find it takes 10-15 mins, start to finish, if that. Tbh you could do it in 5 mins if you rushed. You have all the info you need to upgrade your console without bricking it,i would read it and keep your console working well.

    As for XEX Menu used it to do what? what did not work?
     
  12. darkenn

    darkenn New Member

    Joined:
    Jan 4, 2014
    Messages:
    3
    Likes Received:
    0
    Hello InsaneNutter. First off, thanks so much for the detailed tut. I was able to update the nand and got the dash up to 16537 and retained the jtag. I'm also stuck with the kinect update. I tried following this post:

    https://digiex.net/downloads/downlo...stem-update-2-0-16547-0-download-avatars.html

    But when I plugged in the usb stick containing the $systemupdate folder into the xbox, it doesn't seem to want to update. I've tried rebooting it too with the usb stick plugged in but it goes right into the dash. Is it because it is the same level so it doesn't feel an update is required? Is there a way I can force it to update?

    Please reply at your convenience. Thanks!!
     
  13. InsaneNutter

    InsaneNutter Resident Nutter Staff Member

    Joined:
    Jun 1, 2007
    Messages:
    12,254
    Likes Received:
    3,724
    Location:
    Yorkshire, England
    Ensure the usb memory stick is FAT32 formatted, you can also try renaming the update folder to $$ystemUpdate
     
  14. darkenn

    darkenn New Member

    Joined:
    Jan 4, 2014
    Messages:
    3
    Likes Received:
    0
    Thx for the response. Yes, the USB stick is FAT32. I also tried renaming the folder as you said. Unfortunately the xbox still doesn't recognize it as an update. However, when I turn on the xbox with the kinect attached, it says that I need to do an update and go through xbox live to do so. Any other thoughts?

    I'm guessing it's a bad idea to update over xbox live correct?
     
  15. InsaneNutter

    InsaneNutter Resident Nutter Staff Member

    Joined:
    Jun 1, 2007
    Messages:
    12,254
    Likes Received:
    3,724
    Location:
    Yorkshire, England
    Indeed dont update over xbox live you will find that you no longer have a working console.

    Try renaming it to $ystemUpdate and see if that works, its one of the two and i always forget which.
     
  16. darkenn

    darkenn New Member

    Joined:
    Jan 4, 2014
    Messages:
    3
    Likes Received:
    0
    I fail to read. I didn't realize the U needed to be capital. So just to confirm, $$ystemUpdate was what worked. Thanks so much for all your help!
     
  17. ciotic

    ciotic New Member

    Joined:
    Jan 10, 2014
    Messages:
    2
    Likes Received:
    0
    Hello! I am new on this forum, and I have some questions for you. I have just finished to make my new nand for my xbox 360 slim, but i'm not sure that it is the correct one.
    At this step: "Note: If you are unsure if your console is an Xenon, Zypher, Falcon, Jasper 16mb, Jasper 256mb or Jasper 512mb now would be a good time to make a note of it. As you can see in the image below the revision of the console and nand size is displayed, you will need to know this later on" on my xbox is shown unknown and the nand is only 16mb. I want to know if my motherboard is Trinity with 16 mb.
    Another question: when i opened my nanddump.bin all boxes were completed automatically. In my case was checked: Build type: Freebot RGX 1.x and Motherboard: Trinity
    I want to know if i should leave them like this or i should change them. I'm sorry for my english. I've tried to write as correct as possible. I am waiting for an answer before flashing my xbox with the new dashboard.
    PS: is there a new dashboard than 16537?
     
  18. ciotic

    ciotic New Member

    Joined:
    Jan 10, 2014
    Messages:
    2
    Likes Received:
    0
    PS2: in the xeBuild i saw a Download tab. If I download the dashboard avatars, I must still follow the step nr. 5 in order my kinect to work? Also in this section i saw a button for Download Dashfiles. What are for those files?
     
  19. InsaneNutter

    InsaneNutter Resident Nutter Staff Member

    Joined:
    Jun 1, 2007
    Messages:
    12,254
    Likes Received:
    3,724
    Location:
    Yorkshire, England
    Yes leave them how it is, do not changed anything.
     
  20. beh_kh

    beh_kh New Member

    Joined:
    Jan 16, 2014
    Messages:
    1
    Likes Received:
    0
    hi InsaneNutter! thanks for your tutorial!

    i have a problem! i update my slim rgh to kernel 16537 but... i cant play any games with disc... i put any game in tray and xbox do nothing
     

Share This Page