Xbox 360 Jtag or RGH Hack Easy Update to Dashboard 17502 with XeBuild GUI

hyra said:
I followed all the steps and it did work really well. My dashboard is 2.0.16537 now but when I plug in my kinect, it still requests "more update is required"... What should I do now?
Click to expand...

I had that problem I connected my xbox to my router via ethernet did the same with my laptop and then ran XEBuild v 1.08 I had put the system update for 2.0.16537 into the folder called 16537, Powered up my xbox and went to dash launch then to configure and put updserv set to enabled, then on my laptop ran the file called updatemyconsole.bat

It did the update for me and rebooted my xbox and now it doesn't ask for the kinect update either and the JTag is still there too
 
I tried it but it kept saying that "Fatal error occurred. Cannot find console" even though I already connect them through the router.
 
mens just run the update itself, I suggested what I did due to my console not seeing updates, did a bit of research and found other means, but you could download the system update put it on a disc and away you go
 
hyra said:
what do you mean by "run the 16537 update"?
Click to expand...

You have to get the kinect / avatar data from the official microsoft update.

It is all explained in the first post under: 5. FAQ: How do I restore the avatar and kinetic data so i can use my kinect?
 
Is there a quick guide to doing this or just follow the instructions you put at the top of the forum. Can you email it to me azboy041666@gmail.com? I tried using xexmenu 1.2 but that didn't work. So any advise you can give me will help. Can you get this to me asap? Thank you so much sir. And happy New Year.
 
azboy50 said:
Is there a quick guide to doing this or just follow the instructions you put at the top of the forum. Can you email it to me azboy041666@gmail.com? I tried using xexmenu 1.2 but that didn't work. So any advise you can give me will help. Can you get this to me asap? Thank you so much sir. And happy New Year.
Click to expand...

What's not quick about the above? if you read it you will find it takes 10-15 mins, start to finish, if that. Tbh you could do it in 5 mins if you rushed. You have all the info you need to upgrade your console without bricking it,i would read it and keep your console working well.

As for XEX Menu used it to do what? what did not work?
 
InsaneNutter said:
You have to get the kinect / avatar data from the official microsoft update.

It is all explained in the first post under: 5. FAQ: How do I restore the avatar and kinetic data so i can use my kinect?
Click to expand...

Hello InsaneNutter. First off, thanks so much for the detailed tut. I was able to update the nand and got the dash up to 16537 and retained the jtag. I'm also stuck with the kinect update. I tried following this post:

https://digiex.net/downloads/downlo...stem-update-2-0-16547-0-download-avatars.html

But when I plugged in the usb stick containing the $systemupdate folder into the xbox, it doesn't seem to want to update. I've tried rebooting it too with the usb stick plugged in but it goes right into the dash. Is it because it is the same level so it doesn't feel an update is required? Is there a way I can force it to update?

Please reply at your convenience. Thanks!!
 
Ensure the usb memory stick is FAT32 formatted, you can also try renaming the update folder to $$ystemUpdate
 
InsaneNutter said:
Ensure the usb memory stick is FAT32 formatted, you can also try renaming the update folder to $$ystemUpdate
Click to expand...

Thx for the response. Yes, the USB stick is FAT32. I also tried renaming the folder as you said. Unfortunately the xbox still doesn't recognize it as an update. However, when I turn on the xbox with the kinect attached, it says that I need to do an update and go through xbox live to do so. Any other thoughts?

I'm guessing it's a bad idea to update over xbox live correct?
 
Indeed dont update over xbox live you will find that you no longer have a working console.

Try renaming it to $ystemUpdate and see if that works, its one of the two and i always forget which.
 
InsaneNutter said:
Indeed dont update over xbox live you will find that you no longer have a working console.

Try renaming it to $ystemUpdate and see if that works, its one of the two and i always forget which.
Click to expand...

I fail to read. I didn't realize the U needed to be capital. So just to confirm, $$ystemUpdate was what worked. Thanks so much for all your help!
 
Hello! I am new on this forum, and I have some questions for you. I have just finished to make my new nand for my xbox 360 slim, but i'm not sure that it is the correct one.
At this step: "Note: If you are unsure if your console is an Xenon, Zypher, Falcon, Jasper 16mb, Jasper 256mb or Jasper 512mb now would be a good time to make a note of it. As you can see in the image below the revision of the console and nand size is displayed, you will need to know this later on" on my xbox is shown unknown and the nand is only 16mb. I want to know if my motherboard is Trinity with 16 mb.
Another question: when i opened my nanddump.bin all boxes were completed automatically. In my case was checked: Build type: Freebot RGX 1.x and Motherboard: Trinity
I want to know if i should leave them like this or i should change them. I'm sorry for my english. I've tried to write as correct as possible. I am waiting for an answer before flashing my xbox with the new dashboard.
PS: is there a new dashboard than 16537?
 
PS2: in the xeBuild i saw a Download tab. If I download the dashboard avatars, I must still follow the step nr. 5 in order my kinect to work? Also in this section i saw a button for Download Dashfiles. What are for those files?
 
ciotic said:
Another question: when i opened my nanddump.bin all boxes were completed automatically. In my case was checked: Build type: Freebot RGX 1.x and Motherboard: Trinity
I want to know if i should leave them like this or i should change them. I'm sorry for my english. I've tried to write as correct as possible. I am waiting for an answer before flashing my xbox with the new dashboard.
Click to expand...

Yes leave them how it is, do not changed anything.
 
hi InsaneNutter! thanks for your tutorial!

i have a problem! i update my slim rgh to kernel 16537 but... i cant play any games with disc... i put any game in tray and xbox do nothing
 
You must log in or register to reply here.

About Digiex

Digiex is a technology and gaming forum, founded in 2004 by InsaneNutter and Nimrod. Digiex has served the internet community with breaking news, detailed guides, exclusive downloads and a popular discussion forum. A small, friendly community of like‑minded people has developed over the years. People are encouraged to register and participate in on‑going discussions.

Get Social

Back
Top Bottom